+91 8866188126 [email protected]

EMS · Wire harness & cable assembly

Wire harness & cable assembly — the wiring that ties your product together

Most electronic products need more than a circuit board: power leads, sensor cables and connectors that link boards, displays and switches. Here is what a wire harness is, how one is built, and what to send us so we can quote it for you.

Get an instant quote

See how it works

1/5 · Cut & strip

Each wire is cut to the length on your drawing and its ends are stripped.

How a wire harness is built: Cut & strip — Each wire is cut to the length on your drawing and its ends are stripped. Crimp — A terminal is crimped onto the stripped end, then the crimp is checked. Insert — Terminals click into the connector housing, following your pin-out table. Route & tie — Wires are laid out on a harness board, bundled, tied and labelled. Test — Each circuit is checked for continuity and correct pin-out before packing.

What is a wire harness?

A wire harness (also called a cable harness or wiring loom) is a set of wires, terminals and connectors grouped into one organised unit. Instead of fitting loose wires one by one, the installer plugs in a single, pre-built, tested assembly.

Cable assembly

Usually a single cable — often with an outer jacket — with a connector at one or both ends. Examples: a power lead, a sensor cable or a ribbon cable between two boards.

Wire harness

Many individual wires bundled together, often with branches going to different parts of a machine or enclosure, held by ties, sleeving or tape and identified with labels.

Who it is for

Teams building control panels, industrial machines, instruments, chargers, appliances, vehicle accessories or any product where boards and parts must be connected reliably inside an enclosure.

Why use a pre-built harness?

Fewer wiring mistakes on your assembly line, faster product build, neater routing inside the enclosure and a repeatable result — because each harness is built to the same drawing and checked against it.

How a harness is built — step by step

The exact steps depend on your design, but most harnesses go through the same basic process.

  1. 1

    Drawing & engineering review

    Our team studies your harness drawing, wire list and connector part numbers. Questions about missing lengths, unclear pin-outs or hard-to-get connectors are raised with you before anything is bought.
  2. 2

    Material sourcing

    Wire, terminals, connector housings, sleeving and labels are sourced to your specification. If you prefer to supply some materials yourself, tell us which ones. Read more about how we source parts.
  3. 3

    Cut & strip

    Each wire is cut to the length on the drawing and the insulation is stripped from the ends by the amount the terminal needs.
  4. 4

    Crimp or solder terminals

    Terminals are crimped onto the stripped ends using tooling suited to that terminal, as specified by its manufacturer. Some joints are soldered or sleeved with heat-shrink instead, depending on the design.

    Tip: Crimp terminals and connector housings must come from compatible families — quote the exact part numbers on your drawing.

  5. 5

    Insert into housings

    Crimped terminals are pushed into the connector housing cavities following your pin-out table, and the locks are checked.
  6. 6

    Lay out, bundle & label

    For multi-branch harnesses, the wires are laid on a layout board that matches the drawing, then bundled with ties, sleeving or tape, and labels or markers are added where you need them.
  7. 7

    Test & inspect

    Circuits are typically checked for continuity and correct pin-to-pin connection, and the harness is visually inspected before packing. The checks for your job are agreed during the quote review.

Types of cable and harness work

Tell us what you need — these are the common kinds of jobs customers ask about. We confirm what we can take on after reviewing your drawing.

TypeWhat it isTypical use
Point-to-point cableA single cable or wire set with a connector on each endBoard-to-board, board-to-display, sensor leads
Multi-branch harnessMany wires bundled with branches to different locationsMachines, control panels, enclosures with several boards
Ribbon / flat cableFlat multi-conductor cable with IDC connectorsBoard-to-board links, front panels
Power cablesHeavier-gauge wires for supply and load connectionsPower supplies, chargers, motors
Shielded / coaxial cablesCables with a braid or foil shield around the conductorsSignal and RF lines that need noise protection
Box build wiringHarnesses fitted as part of a complete product buildSee box build assembly

What to send us

The more complete your information, the faster and more accurate the quote.

ItemWhy we need it
Harness drawing (PDF or CAD)Shows the layout, branch points, lengths and where each connector goes
Wire / pin-out tableLists every wire: from connector & pin, to connector & pin, colour and gauge
Connector & terminal part numbersHousings and terminals must match; exact part numbers avoid wrong substitutes
Wire specificationGauge (AWG or mm²), insulation type, colour and any temperature or flexibility needs
Length tolerancesHow precise each length must be
Labels, sleeving & finishMarker text, heat-shrink, braided sleeve, tape or ties
Quantity & target dateSo we can plan sourcing and build
Sample or photos (optional)Very helpful when there is no formal drawing yet

No drawing yet?

That is fine. Send us a photo of an existing harness, a sketch with lengths and the connectors you plan to use, and we will tell you what else is needed before we can quote.

Quality & checks

A harness that looks fine can still have a swapped pin or a loose crimp — these checks are meant to catch that.

Continuity & wiring check

An end-to-end check of each wire is the usual way to catch a missing connection, short or swapped pin before shipping.

Crimp quality

Crimp quality depends on using tooling that matches the terminal. Crimp checks and pull tests on samples can be agreed for your job.

Visual inspection

Strip length, terminal seating, housing locks, labels and bundling are checked against the drawing.

Workmanship standard

IPC/WHMA-A-620 is the widely used workmanship standard for cable and harness assemblies. Read about it on our standards page.

Extra tests on request

High-voltage (hipot) or insulation tests and special acceptance checks can be discussed for your project during the quote review.

Quality documents

See our quality standards page and ask us for current certificate copies.

How to start

  1. 1

    Send your requirement

    Share your drawing, wire list, connector part numbers and quantity through the contact page.
  2. 2

    We review & quote

    Our team checks the details, asks about anything unclear and sends you a quotation for materials and assembly.
  3. 3

    Approve a first sample

    For new designs, a first harness can be built and checked by you before the full quantity is produced.
  4. 4

    Production & delivery

    After approval the harnesses are built, checked and delivered to you.

Need the boards too?

Tell us if the same product also needs boards. FR-4 and flex PCBs up to 16 layers get an instant online price; see our PCB fabrication, PCB assembly and turnkey pages.

Frequently asked questions

No. Harnesses vary too much in wires, connectors and labour, so our team quotes them after reviewing your drawing. Instant online pricing is only for PCBs and PCB assembly. Send us your requirement.

A cable assembly is usually one cable with connectors at its ends. A harness groups many separate wires, often with branches, into one bundle. Both are built and tested in a similar way.

We can source materials to your part numbers, quoted per requirement. If a part is hard to get, we will tell you and ask before changing anything. See global component sourcing.

Tell us which items you plan to send. We confirm during the quote review and quote the rest.

Tell us the class or standard your product needs — for example IPC/WHMA-A-620 — and we confirm during the quote review. Learn more on our certifications & standards page.

Harnesses are often part of a box build, where boards, cables and the enclosure come together as one finished unit. Tell us the full requirement and we quote after review.

Tell us your quantity — prototypes and production runs are both reviewed and quoted per requirement.

Related questions

Learn more — answers to the questions people ask next.

Related guides

Still have a question?

Send us your files or call us — our engineers will help you choose the right options for your boards and assembly.

Streamline your innovation with seamless PCB ordering.

For More Details Contact Us