+91 8866188126 [email protected]

PCB design guide

Choosing a PCB surface finish: HASL, Lead-free HASL, ENIG or OSP

The surface finish is the thin coating on every exposed copper pad of your board. It decides how well parts solder, how flat the pads are and how long the bare boards can wait on the shelf. This guide explains the four finishes in our online calculator in plain words and helps you pick the right one.

Get an instant quote

What a surface finish does

Exposed bare copper oxidises quickly in normal air. Oxidised copper does not wet well with solder, so joints become weak or do not form at all. The finish protects the pads until they are soldered.

Protects the copper

The solder mask covers most of the board, but pads, test points and edge contacts stay open. The finish seals that exposed copper against air and moisture.

Makes soldering reliable

A good finish gives solder a clean, wettable surface, so paste and hand-soldered joints flow and bond properly.

Sets pad flatness

Some finishes leave a slightly domed, uneven layer; others are almost perfectly flat. Flatness matters a lot for small and fine-pitch parts.

Quick answer

For most hobby, prototype and general products, Lead-free HASL is a sensible everyday choice. Pick ENIG for fine-pitch ICs, BGA/QFN packages, keypads or long storage. Choose OSP when you want a flat finish at low cost and will assemble the boards soon. Leaded HASL is the economical option when RoHS is not required.

HASL (with lead)

Hot Air Solder Levelling: the board is dipped in molten tin-lead solder and hot-air knives blow off the excess, leaving a solder coating on every pad.

Where it fits

Economical, robust and very easy to solder by hand, because the pads are already coated with solder. Good for through-hole parts, larger SMD packages (0805, SOIC, etc.), repair-friendly boards and products that do not need RoHS.

Where it does not

The coating is not perfectly flat — pads can end up slightly domed or uneven, which can cause problems with fine-pitch ICs, small passives and BGA/QFN parts. It contains lead, so it is not RoHS compliant and is not suitable for products sold where RoHS applies.

Lead-free HASL

The same process as HASL, but with a lead-free solder alloy. It is the RoHS-compliant everyday choice.

Why choose it

Keeps the strengths of HASL — good solderability, tolerant of hand soldering, long shelf life — while meeting RoHS. A good default for general electronics and most prototypes.

Things to know

Lead-free alloys are processed at higher temperatures, and the surface is still not as flat as ENIG or OSP. For fine-pitch or BGA parts, a flat finish is usually the safer choice.

ENIG — flat gold for fine-pitch and BGA

Electroless Nickel Immersion Gold: a nickel layer is deposited on the copper, then a very thin layer of gold protects the nickel. Solder bonds to the nickel; the gold keeps it clean until then.

Very flat pads

ENIG gives an even, flat surface — ideal for fine-pitch ICs, BGA, QFN/LGA, small passives and stencil printing.

Long shelf life

The gold layer does not tarnish easily, so ENIG boards generally store well. It is also RoHS compliant and good for keypad and contact pads.

Higher cost

ENIG usually costs more than HASL or OSP, because of the gold and the extra chemical steps.
Gold thickness optionWhen to use it
1 U" gold (standard)Normal choice for soldering pads and most products.
2 U" goldA slightly thicker gold layer for a little more protection on contact pads, or for boards that will be stored longer before use. Costs extra — the calculator shows the difference.

Flex boards are ENIG only

ENIG is the only finish offered for flexible PCBs in our online calculator — the finish is set automatically when you choose Flex. See flex PCB capabilities.

OSP — flat and economical, but short-lived

Organic Solderability Preservative: a very thin, clear organic film that bonds to the copper and keeps it from oxidising. It burns off during soldering.

Strengths

Flat like ENIG, lead-free, and economical. A good fit for SMD boards that will be assembled soon after they arrive, including fine-pitch parts.

Limits

Short shelf life — plan to assemble the boards soon. The film is sensitive to handling and moisture, and it typically survives only a limited number of reflow cycles, which matters for double-sided assembly or rework. Pads look like bare copper, which can make visual inspection harder.

Store OSP boards carefully

Keep OSP boards in their sealed packing until assembly, avoid touching the pads with bare fingers, and plan both reflow passes close together if you assemble both sides.

Side-by-side comparison

General guidance only — exact behaviour depends on storage, handling and your assembly process.

FinishPad flatnessRoHSShelf lifeRelative costBest use
HASL (with lead)UnevenNoLongLowThrough-hole, larger SMD, hand soldering, non-RoHS products
Lead-free HASLUnevenYesLongLowEveryday RoHS boards and general prototypes
ENIGVery flatYesLongHigherFine-pitch, BGA/QFN, contact pads, long storage, flex boards
OSPVery flatYesShortLowSMD boards assembled soon after delivery

Which finish is available for your board

Not every finish is offered for every layer count and thickness. Our online calculator shows only the finishes that are possible for your choices and updates the price as you switch.

BoardFinishes in our online calculator
1 layer (FR-4)HASL, Lead-free HASL, ENIG
2 layers (FR-4)HASL, Lead-free HASL, ENIG, OSP — the extra-thin 0.4 mm option needs ENIG
4 layers (FR-4)HASL, Lead-free HASL, ENIG, OSP
6 layers (FR-4)ENIG or OSP
8 to 16 layers (FR-4)HASL, Lead-free HASL, ENIG, OSP
Flex (1 or 2 layers)ENIG only
  1. 1

    Choose material, layers and thickness first

    These decide which finishes are possible. If your current finish is not offered for a new choice, the calculator switches it to one that is (usually ENIG).
  2. 2

    Pick the finish and watch the price

    The instant price updates straight away, so you can compare finishes on your actual board size and quantity. With ENIG you can also choose the gold thickness.
  3. 3

    Check other options that depend on the finish

    Very small vias (0.1 mm) are not possible with HASL — choose ENIG or OSP. See PCB capabilities for all limits.

Gold fingers vs ENIG

They are both gold, but they do different jobs.

ENIG

A thin gold layer over nickel on all exposed pads, mainly to keep them solderable and flat. It is not designed for repeated plugging in and out.

Gold fingers

Hard-gold plated contacts along the board edge that slide into a slot connector, like a memory card. Hard gold is much more wear-resistant for repeated insertion. Choose “Yes, bevelled” to angle the edge for easier insertion.

Can I combine them?

Yes — gold fingers are a separate option from the surface finish, so the rest of the board keeps the finish you choose. Gold fingers are not available on flexible PCBs.

Frequently asked questions

For general boards, Lead-free HASL is a safe, economical choice. If your design has fine-pitch ICs, BGA or QFN parts, choose ENIG.

Only if your product must meet RoHS (for example, for sale in markets that require it). For personal projects and products where RoHS does not apply, leaded HASL is fine and easy to solder.

Our online calculator offers ENIG or OSP for 6-layer boards. It only shows finishes that are possible for the layer count and thickness you selected.

OSP has the shortest shelf life of the four finishes, so plan to assemble soon after delivery and keep the boards sealed until then. If the boards may wait a long time, choose ENIG or HASL.

Most boards do not — 1 U" is standard. Choose 2 U" if you want a little more protection on contact pads or plan to store the boards longer. For connectors that are plugged in often, gold fingers are the better option.

The assembly price is based on solder pads and quantity, not the finish. The finish only affects the bare PCB price. See the assembly quote FAQ.

Related guides

Still have a question?

Send us your files or call us — our engineers will help you choose the right options for your boards and assembly.

Streamline your innovation with seamless PCB ordering.

For More Details Contact Us