+91 8866188126 [email protected]

PCB materials guide

PCB materials, TG, board thickness and copper weight

The base material, its heat rating, the board thickness and the copper weight decide how strong, how heat-resistant and how much current your board can handle. This guide explains each choice in plain words and shows which ones our online calculator prices instantly.

Get an instant quote

Online price or quote by our team?

Most boards get an instant price online. Special materials and grades are still welcome — you send them for a quote and our team emails you the price.

OptionOnline instant priceSend for quote
Base materialFR-4 (rigid), Flex (polyimide)Aluminium, copper core, Rogers, PTFE (Teflon)
LayersFR-4: 1, 2, 4, 6, 8, 10, 12, 14, 16 · Flex: 1 or 218 layers and more
Product gradeIndustrial / consumer electronicsAerospace, medical

What the online price includes

The online price includes GST and shipping, and every board gets a free 100% flying-probe electrical test. The minimum order is 5 PCBs, and bare boards are typically delivered in 10–15 working days in India, including express shipping.

FR-4: the standard board material

FR-4 is a laminate of woven glass fibre bonded with epoxy resin, with copper foil on the surfaces. It is strong, stable, a good electrical insulator and flame-retardant — which is why almost all everyday electronics use it.

Where it fits

Controllers, IoT devices, power supplies, sensors, chargers, industrial boards, hobby and student projects — if you are not sure, FR-4 is almost always the right start.

Instant price online

FR-4 boards from 1 to 16 layers are priced instantly on our quote page. You only choose the layers, size, quantity and options.

Limits to keep in mind

FR-4 does not move heat away well and its electrical properties change at very high frequencies. That is where metal-core and RF laminates come in (see below).

TG — how much heat the laminate tolerates

TG (glass-transition temperature) is the point where the resin starts to soften. Above it the board expands faster, mostly in thickness, which stresses plated holes. A higher TG gives more margin during soldering and in hot environments.

TG gradeTypical use (general guidance)
TG135 (standard)Most 1–6 layer boards with normal soldering and room-temperature use.
TG140 / TG155 (mid)Boards that see several reflow passes, double-sided assembly, or warmer operating conditions.
TG170 (high)Multilayer boards (8 layers and up), thick boards, lead-free assembly at higher temperatures, and products used in hot places.
LayersTG our calculator offers
1 layerTG135
2 layersTG135, TG140, TG155
4 layersTG135, TG140, TG155
6 layersTG135, TG155, TG170
8 layersTG155, TG170
10–16 layersTG170

Why higher TG for 8+ layers and lead-free assembly

Lead-free solder melts at a higher temperature than leaded solder, and a thick multilayer board takes longer to heat through. More heat for longer means more expansion — a higher-TG laminate keeps the plated holes and inner connections reliable. That is why the calculator only offers TG155 and above from 8 layers.

Board thickness

Thickness is the finished thickness of the whole board, copper and solder mask included. 1.6 mm is the standard and fits most enclosures, connectors and card-edge sockets.

LayersThickness options online (mm)
1 layer0.8, 1.0, 1.2, 1.6, 2.0
2 layers0.4 (with ENIG finish only), 0.6, 0.8, 1.0, 1.2, 1.6, 2.0
4, 6 and 8 layers0.8, 1.0, 1.2, 1.6, 2.0
10 layers1.0, 1.2, 1.6, 2.0
12 layers1.2, 1.6, 2.0, 2.5
14 and 16 layers1.6, 2.0, 2.5

Thinner (0.4–1.0 mm)

Small, light products such as wearables, sensor tags and modules that sit inside tight housings. Thin boards bend more, so large thin boards can warp during assembly.

Standard (1.6 mm)

The safe default. Most connectors, mounting hardware and edge-connector sockets are made for it, and it is easy to assemble.

Thicker (2.0–2.5 mm)

Extra stiffness for large or heavy boards, boards with heavy parts or many plug-in cycles, and high layer counts that need room for all the layers.

Thickness that needs a specific finish

On 2-layer boards, 0.4 mm is only available with the ENIG surface finish. If you pick 0.4 mm, choose ENIG — other finishes cannot be ordered at that thickness.

Copper weight

Copper weight is given in ounces (oz): the weight of copper spread over one square foot. 1 oz equals about 35 µm thick. Thicker copper carries more current and spreads heat better, but makes fine traces and gaps harder to etch.

CopperWhere it is used (general guidance)Online options
1 oz (35 µm)Standard for signals and most power traces.Outer layers: all FR-4 boards
2 oz (70 µm)Motor drivers, power supplies, battery and LED boards with higher current.Outer layers: all FR-4 boards
2.5, 3.5, 4.5 ozHeavy current paths, bus bars on board, heat spreading.Outer layers: 2-layer boards
0.5, 1, 2 oz (inner)Inner layers carry ground and power planes and buried signals.Inner layers: 4+ layer boards
  1. 1

    Start from the current your traces must carry

    Find your highest-current paths (power input, motor or LED outputs) and how hot you allow them to get.
  2. 2

    Check trace width with a calculator

    Use any IPC-2221/2152 trace-width calculator. For the same current, 2 oz copper needs roughly half the width of 1 oz.

    Tip: If widening the trace solves the problem, staying on 1 oz is usually cheaper.

  3. 3

    Match the design rules to the copper

    Heavier copper needs wider minimum trace and gap spacing. Set your design rules for the copper you choose before routing.
  4. 4

    Choose the same copper weight online

    Select outer (and, on 4+ layers, inner) copper weight on the quote page so the price matches your design. See PCB capabilities for the full option list.

Flexible (polyimide) boards

Flex boards use thin polyimide film instead of glass-epoxy, so they can bend, fold and fit into curved or moving parts — cameras, hinges, wearables and display connections.

Flex optionWhat our calculator offers
Layers1 or 2
1-layer thickness / copper0.07 mm (1/3 oz), 0.11 mm (1/2 oz), 0.12 mm (1 oz)
2-layer thickness / copper0.11 mm (1/3 oz), 0.12 mm (1/2 oz), 0.20 mm (1 oz)
Surface finishENIG
Maximum size600 × 250 mm

Flex is priced instantly online

Choose Flex as the base material on the quote page — thickness and copper are linked, so the calculator sets the matching copper for you. Full details are on Flex PCB capabilities.

Metal-core and RF materials (send for quote)

These materials solve problems FR-4 cannot: getting heat out fast, or keeping signals clean at very high frequencies. They are priced by our team — choose the material, send it for a quote and we email your quotation.

Aluminium core

A thin circuit layer on an aluminium base. The metal pulls heat away from LEDs and power parts. Typical uses: LED lights, street lights, power modules. Usually single-sided.

Copper core

Like aluminium core but with a copper base, which conducts heat even better. Used for very high-power LEDs and power electronics where heat is the main limit.

Rogers (RF laminates)

Laminates with stable, low-loss electrical properties at high frequencies. Used in antennas, radar, RF front-ends and high-speed links.

PTFE (Teflon)

Very low signal loss at microwave frequencies. Used for demanding RF and microwave circuits. Harder to process, so it is quoted case by case.

Product grade

Product grade sets how strict inspection and documentation are.

GradeWho it is forPricing
Industrial / consumerNormal grade for almost every product.Instant price online
AerospaceProducts that need stricter inspection and documentation.Priced by our team
MedicalMedical devices that need stricter inspection and documentation.Priced by our team

Quick selection table

A starting point only — always check your own design, enclosure and current needs. All rows except the last three can be ordered online.

ApplicationMaterialTGThicknessCopper
Hobby, student, simple control boardFR-4, 1–2 layersTG1351.6 mm1 oz
IoT / microcontroller boardFR-4, 2–4 layersTG135–TG1551.0–1.6 mm1 oz outer, 0.5–1 oz inner
Wearable or small moduleFR-4, 2–4 layers, or FlexTG135–TG1550.6–1.0 mm (Flex: 0.07–0.2 mm)1 oz
Power supply, motor driver, chargerFR-4, 2–4 layersTG1551.6 mm2 oz (heavier on 2 layers)
Dense digital, high-speed (8+ layers)FR-4, 8–16 layersTG1701.6–2.0 mm1 oz outer, 0.5–1 oz inner
Hinge, camera, display cableFlex, 1–2 layers—0.11–0.2 mm1/3–1 oz (set by thickness)
LED lighting, power modulesAluminium or copper core—Send for quoteSend for quote
Antenna, RF, microwaveRogers or PTFE—Send for quoteSend for quote
Aerospace / medical productsAs required—Send for quoteSend for quote

Frequently asked questions

FR-4, TG135, 1.6 mm, 1 oz copper. It suits most designs, gets an instant price and is the easiest to assemble. Change only what your design really needs.

Often it does, though the difference is usually small. From 8 layers only higher-TG laminates are offered, so there is no lower-TG option to compare against. The quote page shows the price as soon as you change the option.

You can request them online: choose the material and send it for a quote. Our team prices these boards and emails you the quotation, which you can then order from.

The calculator only shows thicknesses available for your layer count. If you need something else, contact us with your files and our engineers will check what is possible.

Our engineers check every file before production. If the price has to change, you can accept and pay the difference, or cancel the order and get a refund. See the online ordering FAQ.

Related guides

Still have a question?

Send us your files or call us — our engineers will help you choose the right options for your boards and assembly.

Streamline your innovation with seamless PCB ordering.

For More Details Contact Us